Back
ID # 13369181

Stump Grinder - Skid Steer Mnt, Hyd 12-22gpm

  • Stump Grinder Skid Steer Mnt, Hyd 12 22gpm
  • Stump Grinder Skid Steer Mnt, Hyd 12 22gpm
  • Stump Grinder Skid Steer Mnt, Hyd 12 22gpm
  • Stump Grinder Skid Steer Mnt, Hyd 12 22gpm
  • Stump Grinder Skid Steer Mnt, Hyd 12 22gpm
  • Video Button Maxresdefault
Videos
Half Day: $$150.00
Day: $150.00
Weekend: $225.00
Week: $600.00
Month: $1800.00
 Get a Quote  Request Rental  Get Financed  Value a Trade  Contact Us  Book a Demo   Get Directions  Print
Overview
Designed simply and ruggedly the S14 has a heavy duty fixed deflector. The simple direct flow hydraulic drive is designed to provide the best torque and RPM to the cutting head. The unique positioning of the rotor allows the operator an excellent view of the grinding action. The S14 is also available with a mini skid steer mount for even better access to tight areas.
The cutting wheel is powered by the hydraulic remotes on your Skid Steer and the swing cylinder is controlled with a 12v diverter valve. The off set rotor design for greater visibility and needle valve for precise swing control makes the S24 & S28 comfortable to operate. 34 teeth on a 24” cutter means less cutting for each tooth resulting in longer tooth life and smother cutting for less wear on your Skid Steer.
Units are shipped with standard skid steer quick attach, 12v cigarette light plug, and flat-face quick couplers. The floating deflector contains the chips and debris and can be swung completely out of the way to cut close to fences.
Grease zerks and replaceable brass bushings provided at major pivot points for extended service life. Heavy tooth population makes finer mulch and allows much smoother operation.

Cutting Depth - Below Ground: 6"
Self Feeding - S14

TIP: Grass saver. Since cutting is done by backing away from the stump, and repositioning is usually only a few inches, the S14 causes very little turf damage in the hands of an experienced skidsteer operator.
  SKID STEER - STUMP CUTTING TIMES
Model Motor
Option		 10 GPM 12 GPM 15 GPM 20 GPM 24 GPM 30 GPM 35 GPM 40 GPM
S14 S250 15 min 10 min 8 min -- -- -- -- --
  S450 18 min 12 min 10 min 6 min -- -- -- --
S18 S450 20 min 15 min 12 min 10 min -- -- -- --
  S550 20 min 15 min 12 min 10 min 8 min -- -- --
  S650 -- -- -- -- 15 min 7 min 6 min 5 min
S24 S450 -- -- -- 20 min 12 min -- -- --
  S550 -- -- -- 20 min 12 min 10 min 8 min --
S28 S650 -- -- -- -- -- 6 min 5 min 4 min

Double all sizes for intermittent.
Model Motor
Option		 10 GPM 12 GPM 15 GPM 20 GPM 24 GPM 30 GPM 35 GPM 40 GPM
S14 S250 30 min 20 min 12 min -- -- -- -- --
  S450 40 min 25 min 15 min 10 min -- -- -- --
S18 S450 50 min 30 min 20 min 15 min -- -- -- --
  S550 50 min 30 min 20 min 15 min 10 min -- -- --
  S650 -- -- -- -- 20 min 15 min 12 min 10 min
S24 S450 -- -- -- 35 min 25 min -- -- --
  S550 -- -- -- 35 min 25 min 20 min 15 min --
S28 S650 -- -- -- -- -- 10 min 8 min 6 min

Double all sizes for intermittent.
Model Motor
Option		 10 GPM 12 GPM 15 GPM 20 GPM 24 GPM 30 GPM 35 GPM 40 GPM
S18 S450 -- -- 60 min 40 min -- -- -- --
  S550 -- -- 60 min 40 min 30 min -- -- --
  S650 -- -- -- -- 45 min 20 min 15 min 15 min
S24 S450 -- -- -- -- 50 min -- -- --
  S550 -- -- -- -- 50 min 40 min 30 min --
S28 S650 -- -- -- -- -- 20 min 15 min 12 min

Double all sizes for intermittent.
  STUMP GRINDERS · SKID STEER SPECIFICATIONS
Model No. S 14 S 18 S 24 S 28
Recommended HP Size 12-30 25-80 30-80 50-120
Maximum HP Size Check GPM & PSI Check GPM & PSI Check GPM & PSI Check GPM & PSI
Hydraulic GPM Check Motor Options Check Motor Options Check Motor Options 30-40
Rotor Size 18” 24” 24” 24”
Number of Teeth 12 34 34 34
Tooth Construction Green Carbide Steel Bolt-In Carbide Steel Bolt-In Carbide Steel Bolt-In
Cutting Wheel Speed 700 RPM 700 RPM 700 RPM 800 RPM
Cutting Height - Above Ground No Limit No Limit No Limit No Limit
Cutting Depth - Below Ground 6” 10” 10” 10”
Maximum Cutting Depth - Per Pass 2” 5” 6” 6”
Maximum Horizontal Cut 12” 22” 22” 22”
Swing Arc 0° 0° 80° 80°
Hub Torque 150 Ft.-Lbs. 250 Ft.-Lbs. 250 Ft.-Lbs. 803 Ft.-Lbs.
Over Torque Protection Relieve Valve Relieve Valve Relieve Valve Relieve Valve
Hitch Mini Plate Quick Attach Quick Attach Quick Attach
No. Of Remotes Required - Hydraulic 1 1 1 1
Requires 12 Volt DC No No Yes Yes
Input Speed -- -- -- --
Unit Weight (Shipping) Lbs. 394 702 852 995
Width (Shipping) 44” 48” 48” 48”
Length (Shipping) 41” 48” 56” 56”

Match GPM & PSI Results to a Model
Model Identifies Motor Option

Model Recommended
GPM		 Max GPM* Requires
Case Drain		 Hydraulic
Couplers		 Motor Options
S14 10-15
12-22		 16 GPM
23 GPM		 No
No		 Included
Included		 S250
S450
S18 12-22
12-27
25-40		 23 GPM
28 GPM
42 GPM		 No
Yes**
Yes**		 Included
Included
Not Supplied		 S450
S550
S650
S24 20-26
22-32		 28 GPM
35 GPM		 Yes**
Yes**		 Included
Not Supplied		 S450
S550
S28 30-40 42 GPM Yes** Not Supplied S650
*NOTICE: This value must never be exceeded or warranty is voided. Will cause equipment damage.
**Note required for bottom of GPM Range
FEATURES

Remote

Stump Blaster remote control

This 12V remote allows you to control your Stump Blaster from within the cab of your skid steer. This remote comes standard with S24 and S28 models.

Excavator Mount

Stump Blaster excavator mount

This standard mounting plate is perfect for welding to your machine's unique fitting.

More Clearance

Clearance on Stump Blaster in action

The Stump Blaster's carbide teeth extend a full 1 1/4 inches from the rotor. This prevents chips and mulch from getting plugged up during grinding. Greater chip clearing produces smoother operation and reduces heat build-up that could damage the rotor and cause premature tooth failure.

Carbide Tipped

Carbide Tipped Cutting Teeth on Stump Blaster

Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable, gravel, stones even metal posts are not uncommon to "find". Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.

Floating Deflector

Floating Deflector on Stump Blaster

The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.

More Teeth

Teeth on Stump Blaster in action

Many hands make light work, or in this case fine mulch faster and easier. The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of these rugged teeth, which last longer and typically only need 2 or 3 replaced at a time. The bolt-on designed teeth allow for straightforward replacement.

Hydraulic Motor

Hydraulic Motor on Stump Blaster

Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options.

Rotor

Rotor on Stump Blaster

The massive 3/4 inch thick steel rotor provides the back bone for the Stump Blaster Cutting system. It is the anchor for the carbide tipped teeth. For smooth operation it is important that the rotor remains solid with no flexing. The impressively rugged rotor also provided the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.

Flow Control

Flow control adjustment on Stump Blaster

Fine tune the performance of your Stump Blaster with the Flow Control.

 

Specifications
Model
New Model
Category Name
Stump Grinder
Year
2015
Sale Type
Rent
Manufacturer
Bauma Light
Videos

Videos

Privacy |  Terms |  Site Map |  Login
© 2024 Woolwich Rentals & Sales